





SPE Motorsport S100275 Drain Valve Upgrade for SPE (CAT) Fuel Filter System (2017-2026 6.7L PowerStroke)
Fits: Ford 6.7L (2017-Current Powerstroke)
Diesel Dollars is Southern Diesel Supply's Loyalty Program. Purchasing with Us Earns you 1 Point for every 1 Dollar spent to use for future buys!
By ordering the SPE Motorsport S100275 Drain Valve Upgrade for SPE (CAT) Fuel Filter System (2017-2026 6.7L PowerStroke) you will earn 26 DIESEL DOLLARS in your SDS Fuel Tank!
The SPE Motorsport S100275 is a brass ball-type drain valve that takes the place of the stock petcock on the SPE (CAT) fuel filter system for 2017-2026 6.7L Power Stroke Super Duty trucks. It opens and closes with a quick lever, and a hose nipple lets you route drained fuel into a container.
Important: this valve only works with the SPE upgraded (CAT) fuel filter system. It is an add-on for that system and does not fit the factory fuel filter housing. You can pick up the SPE Motorsport Fuel Filter System here if you do not have it yet.
Fitment
SPE lists the valve for:
- 2017+ Ford F250 (including cab & chassis)
- 2017+ Ford F350 (including cab & chassis)
- 2017+ Ford F450 (including cab & chassis)
- 2017+ Ford F550 (including cab & chassis)
It only has a place to go on a truck that already has the SPE fuel filter system installed. SPE states that the filter system does not fit extended cab, single cab or cab and chassis trucks, so check that your truck can take the filter system before you order. Not sure? Call us with your VIN.
Why this part
A water separator only protects the pump if you actually drain it, and a small, awkward petcock makes that a messy chore. This ball valve gives you a larger handle and a cleaner pour. Add a length of 3/8-inch fuel hose to the included nipple and the water and fuel go into a bottle rather than down your arm.
- Brass body with a stainless steel lever and ball
- Diesel-resistant PTFE seals the ball inside the valve
- 1/8-inch NPT drain port
- 1/8-inch NPT to 3/8-inch hose nipple for draining through fuel hose
What you get
- Ball valve assembly
- Black anodized aluminum 3/8-inch hose nipple fitting
The 3/8-inch fuel hose is not included.
Specifications
- Part number: S100275
- Body: brass; lever and ball: stainless steel
- Internal seal: PTFE
- Drain port: 1/8-inch NPT
- Hose fitting: 1/8-inch NPT to 3/8-inch nipple, black anodized aluminum
- Use: SPE (CAT) fuel filter system only
Installation notes
SPE describes this as a simple install: the valve replaces the stock petcock on the SPE filter system. If you would rather have it done, our Wildwood, FL shop can fit it when we service your fuel filters.
About SPE Motorsport
SPE Motorsport, short for Snyder Performance Engineering, builds parts for Ford diesels out of Latrobe, Pennsylvania. Its 6.7L Power Stroke line leans hard on fuel system protection. See the full SPE Motorsport lineup.
Frequently asked questions
Will this fit my factory fuel filter housing?
No. It is made for the SPE (CAT) fuel filter system only. If you are running the factory setup and want a stronger drain valve, look at the SPE S100102 Gen-2 Billet Fuel Drain Valve instead.
Do I need a hose?
Only if you want to route the fuel into a container. The nipple takes standard 3/8-inch fuel hose, which you supply.
Questions on fitment? Call the shop at the number in the header. We install everything we sell.
✓ added to your cart
Finish the job
Parts our Wildwood techs pair with this one — take a look before you check out.

Diesel Dollars is Southern Diesel Supply's Loyalty Program. Purchasing with Us Earns you 1 Point for every 1 Dollar spent to use for future buys!
By ordering the SPE Motorsport S100275 Drain Valve Upgrade for SPE (CAT) Fuel Filter System (2017-2026 6.7L PowerStroke) you will earn 26 DIESEL DOLLARS in your SDS Fuel Tank!



