{"title":"RAM, (2019-2024) 6.7L Cummins, Digital Monitors, Accessories","description":"\u003cdiv class=\"sds-copy-intro\"\u003e\u003cp\u003eThis page holds sensor add-ons for Edge monitors on the 2019-2024 Ram 2500 and 3500 with the 6.7L Cummins. Know this first: an Edge Insight CTS3 already reads the factory boost, exhaust temperature and transmission temperature data through the OBD-II port. These kits add a separate external sensor to the monitor, on top of what the truck already reports.\u003c\/p\u003e\u003c\/div\u003e\u003cdiv class=\"sds-copy-guide\"\u003e\n\u003ch2\u003eMonitor accessories for the 2019-2024 RAM 6.7L Cummins\u003c\/h2\u003e\n\u003cp\u003eEdge builds its monitors to take external sensors. The EAS kits in this collection cover exhaust gas temperature and pressure, and Edge lists them for its CS2, CTS2 and CTS3 monitors. On a fifth-generation Ram HD, the monitor already pulls a lot from the factory data stream over OBD-II. A sensor kit is about adding a reading from a sensor you install, not replacing what the \u003ca href=\"\/collections\/cummins\"\u003e6.7L Cummins\u003c\/a\u003e already reports.\u003c\/p\u003e\n\u003ch2\u003eWhat to know before you buy\u003c\/h2\u003e\n\u003cp\u003eThere's no known hardware failure pattern for monitors on this platform. The thing owners run into is the Security Gateway Module on 2018 and newer trucks. It allows reads and blocks write functions like tire-size changes, remote start setup and flashing. A monitor with added sensors only reads, so the gateway leaves it alone. The CTS3 is monitoring only. It does not tune the engine, and adding a sensor doesn't change that.\u003c\/p\u003e\n\u003ch2\u003eWhat we carry\u003c\/h2\u003e\n\u003cp\u003eThe accessories here come from \u003ca href=\"\/collections\/edge-products\"\u003eEdge Products\u003c\/a\u003e:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eEdge EAS EGT Kit, Daily Driver\/Tow Kit\u003c\/strong\u003e: an exhaust gas temperature sensor kit that feeds an Edge monitor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEdge EAS Pressure Sensor (0-100 PSI)\u003c\/strong\u003e: a pressure sensor with a 0 to 100 psi range for an Edge monitor.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eWhere you plumb the pressure sensor decides what it reads. Tell us what you want to watch and we'll help match the sensor to the job.\u003c\/p\u003e\n\u003ch2\u003eFitment notes\u003c\/h2\u003e\n\u003cp\u003eThese are Edge accessories for Edge CS2, CTS2 and CTS3 monitors. If you run a different brand of gauge, check with us before ordering. If you're also shopping for a mount, Edge's 38603 A-pillar mount fits 2019-2026 Ram 2500 and 3500 pickups that don't have the factory Head-Up Display. When in doubt, verify by VIN.\u003c\/p\u003e\n\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\n\u003ch3\u003eWhy add an EGT sensor if the monitor already shows EGT?\u003c\/h3\u003e\n\u003cp\u003eThe CTS3 reads the factory exhaust temperature data over OBD-II. The EAS EGT kit adds Edge's own external sensor to the monitor, and Edge packages it as a daily driver and tow kit. If you aren't sure you need the second reading, call us and talk it through.\u003c\/p\u003e\n\u003ch3\u003eWhich monitors do these Edge sensors work with?\u003c\/h3\u003e\n\u003cp\u003eEdge lists its EAS EGT and 0-100 psi pressure sensor kits for the CS2, CTS2 and CTS3 monitors. The monitor we sell for this truck is the Insight CTS3, so the two pair up.\u003c\/p\u003e\n\u003ch3\u003eDoes adding a sensor change how the engine runs?\u003c\/h3\u003e\n\u003cp\u003eNo. The sensor sends a reading to the monitor, and the monitor only reads data. It does not write to the engine computer or change the calibration.\u003c\/p\u003e\n\u003ch3\u003eCan you install a sensor kit for me?\u003c\/h3\u003e\n\u003cp\u003eYes. We install everything we sell at our shop in Wildwood, FL. Bring the truck in and we'll mount the sensor and get the reading on your monitor.\u003c\/p\u003e\n\u003cp class=\"sds-copy-cta\"\u003eNot sure what fits? Call the shop at the number in the header, or use the fitment checker on any product page. We install everything we sell.\u003c\/p\u003e\n\u003c\/div\u003e","products":[{"product_id":"edge-products-98620-eas-egt-kit-daily-driver-tow-kit","title":"Edge Products 98620 EAS EGT Kit - Daily Driver\/Tow Kit","description":"\u003cdiv class=\"sds-pd-intro\"\u003e\u003cp\u003eThe Edge Products 98620 EAS EGT Kit, Edge's Daily Driver\/Tow Kit, puts exhaust gas temperature on the Edge monitor on your dash. It includes the EAS Starter Cable, EGT probe, manifold fitting and wiring. Edge calls it its most popular EAS accessory, built so the average diesel truck owner can keep an eye on EGTs.\u003c\/p\u003e\u003c\/div\u003e\u003cdiv class=\"sds-pd-body\"\u003e\n\u003ch2\u003eFitment\u003c\/h2\u003e\n\u003cp\u003eThe 98620 is not tied to a truck year or engine. It is part of Edge's EAS accessory system, which adds readings to a CS2, CTS2 or CTS3 monitor that the monitor can't get from the OBD-II port alone. The monitor is not part of this kit. The probe mounts in the exhaust manifold, and most applications will require the manifold be drilled and tapped to 1\/8-NPT. Look at your manifold before you order. If you want a second set of eyes on it, call us with your year, engine and VIN.\u003c\/p\u003e\n\u003ch2\u003eWhy this part\u003c\/h2\u003e\n\u003cp\u003eEdge named this the Daily Driver\/Tow Kit, and that is who it is for: owners who want exhaust gas temperatures on screen while they drive and tow. The reading is only as good as the probe location. Edge says the external temperature probe must be installed in the exhaust manifold for the most accurate temperature readings, and the closer to the combustion chamber, the better. Once the probe is in, your EGTs show up on your in-cabin device along with the other readings the monitor shows. Edge monitors let you set your own alerts, so the screen can warn you instead of you staring at a number all day.\u003c\/p\u003e\n\u003ch2\u003eWhat you get\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eEAS Starter Cable\u003c\/li\u003e\n\u003cli\u003eEGT probe\u003c\/li\u003e\n\u003cli\u003eManifold fitting\u003c\/li\u003e\n\u003cli\u003eWiring\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot included: the drill bit and 1\/8-NPT tap for the manifold.\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eFeatures\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eEAS Accessory System\u003c\/li\u003e\n\u003cli\u003ePlug and Play Installation\u003c\/li\u003e\n\u003cli\u003eMonitor your EGTs from your in-cabin device\u003c\/li\u003e\n\u003cli\u003eManifold must be drilled and tapped for probe installation\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eProbe port: 1\/8-NPT, drilled and tapped in the exhaust manifold (bit and tap not included).\u003c\/p\u003e\n\u003ch2\u003eInstallation notes\u003c\/h2\u003e\n\u003cp\u003eThe wiring is plug and play through the EAS system, and the kit includes the EAS Starter Cable. The probe is the real work. Most applications will require the manifold be drilled and tapped to 1\/8-NPT, and the bit and tap are not included, so have them on hand before you start. Put the probe in the exhaust manifold, as close to the combustion chamber as you can, for the most accurate readings. If you would rather not drill your own manifold, our Wildwood, Florida shop installs what we sell.\u003c\/p\u003e\n\u003ch2\u003eAbout Edge Products\u003c\/h2\u003e\n\u003cp\u003eEdge Products started in Ogden, Utah, in 1999 and builds in-cab monitors, plug-in modules and emissions-compliant tuners for diesel trucks. Its monitors put boost, EGTs, trans temp and other readings on one screen, with alerts you set yourself. The monitor side is the part of the Edge line we use most in our shop. See it all on our \u003ca href=\"\/collections\/edge-products\"\u003eEdge Products page\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\n\u003ch3\u003eDo I have to drill my exhaust manifold?\u003c\/h3\u003e\n\u003cp\u003eMost likely. Edge says most applications will require the manifold be drilled and tapped to 1\/8-NPT. The bit and tap are not included.\u003c\/p\u003e\n\u003ch3\u003eWhere should the EGT probe go?\u003c\/h3\u003e\n\u003cp\u003eIn the exhaust manifold. Edge says the closer to the combustion chamber, the better, for the most accurate reading.\u003c\/p\u003e\n\u003ch3\u003eWhich monitors work with it?\u003c\/h3\u003e\n\u003cp\u003eEdge's EAS sensor kits work with the CS2, CTS2 and CTS3 monitors. The monitor is sold on its own. This kit covers the EGT probe, manifold fitting, wiring and EAS Starter Cable.\u003c\/p\u003e\n\u003cp class=\"sds-pd-cta\"\u003eQuestions on fitment? Call the shop at the number in the header. We install everything we sell.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":50683620196640,"sku":"98620","price":199.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0916\/3043\/6640\/files\/cf49d9232fb86f4b7e9dfd1d857fecc2c01f9cf8_jpg.avif?v=1757437038"},{"product_id":"edge-products-98607-eas-pressure-sensor-0-100-psi","title":"Edge Products 98607 EAS Pressure Sensor (0-100 PSI)","description":"\u003cdiv class=\"sds-pd-intro\"\u003e\u003cp\u003eThe Edge Products 98607 EAS Pressure Sensor reads 0-100 PSI and plugs into Edge's EAS Universal Sensor Input system (p\/n 98605). Hooked to a CTS2 or CTS3 monitor, it lets you watch a pressure your monitor can't pull from the OBD-II port, such as boost, lift pump pressure or air bag pressure.\u003c\/p\u003e\u003c\/div\u003e\u003cdiv class=\"sds-pd-body\"\u003e\n\u003ch2\u003eFitment\u003c\/h2\u003e\n\u003cp\u003eThe 98607 is not tied to a truck year or engine. It works through Edge's EAS accessory system and is listed as compatible with the CTS2 and CTS3 monitors. To connect it to your monitor you need the EAS Universal Sensor Input Kit (P\/N 98605), which is not included. It is a 1\/8 NPT sensor, so the spot you want to measure needs a 1\/8 NPT port. If you are not sure your monitor and truck are set up for it, call us before you order.\u003c\/p\u003e\n\u003ch2\u003eWhy this part\u003c\/h2\u003e\n\u003cp\u003eYour monitor can only show what the truck reports through the OBD-II port. EAS sensors fill in the rest. The 98607 comes equipped with the proper wires and connectors to plug right into the Universal Sensor Input system, so you skip cutting, splicing and crimping wire terminals. That saves time and money on the install. Edge lists it for monitoring data such as Boost PSI, Fuel Rail Pressure, Air Bag Pressure, Lift Pump Pressure, Pre and Post Intercooler Pressure, and more. The sensor is rated 0 - 100 PSIg, so pick a point whose pressure stays inside that range.\u003c\/p\u003e\n\u003ch2\u003eWhat you get\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eEdge Products 98607 EAS Pressure Sensor, 0 - 100 PSIg, 1\/8 NPT\u003c\/li\u003e\n\u003cli\u003eThe wires and connectors to plug right into the EAS Universal Sensor Input system\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot included: EAS Universal Sensor Input Kit (P\/N 98605).\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eFeatures\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0-100 PSI Capable\u003c\/li\u003e\n\u003cli\u003eEasy Setup Through EAS\u003c\/li\u003e\n\u003cli\u003eCompatible With CTS2\/CTS3\u003c\/li\u003e\n\u003cli\u003eMonitor Pressures On Your Vehicle\u003c\/li\u003e\n\u003cli\u003eRequires EAS Universal Sensor Input Kit To Connect To Device (P\/N 98605) Not Included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eManufacturer warranty:\u003c\/strong\u003e 1 Year\u003c\/p\u003e\n\u003ch2\u003eAbout Edge Products\u003c\/h2\u003e\n\u003cp\u003eEdge Products was founded in 1999 and is based in Ogden, Utah. It builds in-cab monitors, plug-in modules and emissions-compliant tuners for diesel pickups. Its EAS sensor kits, this pressure sensor among them, add readings a monitor can't get from the OBD-II port alone. Browse the line on our \u003ca href=\"\/collections\/edge-products\"\u003eEdge Products page\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\n\u003ch3\u003eDoes the 98607 work by itself?\u003c\/h3\u003e\n\u003cp\u003eNo. It needs the EAS Universal Sensor Input Kit (P\/N 98605), sold separately, to connect to your monitor. The sensor's wires and connectors plug straight into that kit.\u003c\/p\u003e\n\u003ch3\u003eWhich monitors does it work with?\u003c\/h3\u003e\n\u003cp\u003eEdge lists it as compatible with the CTS2 and CTS3. Setup runs through EAS on the monitor.\u003c\/p\u003e\n\u003ch3\u003eWhat can I measure with it?\u003c\/h3\u003e\n\u003cp\u003eEdge lists boost, fuel rail pressure, air bag pressure, lift pump pressure, and pressure before and after the intercooler. Pick a point that stays within 0-100 PSI and has a 1\/8 NPT port.\u003c\/p\u003e\n\u003cp class=\"sds-pd-cta\"\u003eQuestions on fitment? Call the shop at the number in the header. We install everything we sell.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":51511626498336,"sku":null,"price":229.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0916\/3043\/6640\/files\/edge-products-98607-eas-pressure-sensor-0-100-psi-9151258.jpg?v=1779541029"}],"url":"https:\/\/www.southerndieselsupply.com\/collections\/ram-2019-2024-6-7l-cummins-digital-monitors-accessories.oembed","provider":"Southern Diesel Supply","version":"1.0","type":"link"}